Questions? Call Us!

1-800-486-5542

Klein® Bars & Pins

Shop Hand Tools

KleinConnecting Bars

Provide extra leverage when positioning steel members and aligning bolt holes. These drop-forged fit-up bars are pointed on one end; the chisel-end is available straight or at a 15° angle to give greater leverage. Hexagonal or round.

Klein Connecting Bar - Round Klein Connecting Bar - Round

Round Bars

Mfg. # CSI Ref. # Diameter Length
in. mm in. cm
3245 CS-11-2115 3/4 19.1 30 76
3246 CS-11-2116 7/8 22.2 36 91
3247 CS-11-2117 3/4 19.1 24 61
3248 CS-11-2118 7/8 22.2 30 76
3241* CS-11-2119 3/4 19.1 30 76

* Similar to round bar No. 3245 above but chisel-end is straight.

Klein Connecting Bar - Hexagonal Klein Connecting Bar - Hexagonal

Hexagonal Bars

Mfg. # CSI Ref. # Hex. Diameter Length
in. mm in. cm
3242 CS-11-2120 3/4 19.1 30 76
3243 CS-11-2121 7/8 22.2 36 91
3244 CS-11-2122 3/4 19.1 24 61
3240* CS-11-2123 3/4 19.1 30 76

* Similar to hexagonal bar No. 3242 above but chisel-end is straight.

Klein Barrel-Type Drift Pin

Barrel-Type Drift Pins

Machined from forge-quality alloy steel. Tapers are uniform and blend into body diameter. Tough, drop-forged steel will properly end-pein in use. Heat-treated. Black finish.

Mfg. # CSI Ref. # Max. Diameter Point Diameter Overall Length
in. mm in. mm in. mm
3260 CS-11-2124 11/16 17.5 5/16 7.9 7-1/2 191
3261 CS-11-2125 13/16 20.6 7/16 11.1 8 203
3262 CS-11-2126 15/16 23.8 1/2 12.7 8 203
3263 CS-11-2127 1-1/16 27 9/16 14.3 8 203

All dimensions are nominal.

Klein Broad Head Bull Pin

Broad-Head Bull Pins

Mfg. # CSI Ref. # Top Diameter Point Diameter Length
in. mm in. mm in. mm
3255 CS-11-2128 1-1/4 31.8 5/16 7.9 13 330
3256 CS-11-2129 1-1/16 27 1/4 6.4 10 254

All dimensions are nominal

A drop-forged, heat-treated bull pin which increases efficiency by providing a larger striking surface. Design of the head also reduces chance of pin slipping from the hand when aligning holes. Angled head and smooth blending of radii increase strength and reduce the danger of chipping. Below the head, squared-off shoulders have been forged to provide a surface for applying wrench to loosen wedged bull pins. Long, even taper reduces binding and hang-up. Klein broad-head bull pins offer added resistance to “mushrooming”, permitting much longer use than is possible with conventional designs. Black finish. Note: OSHA specifically states that, “impact tools such as drift pins, wedges, and chisels, shall be kept free of mushroomed heads.”

Klein Bull-Pin Holder Klein Bull-Pin Holder

Bull-Pin Holders

Holders for Klein bull pins. Attach to belt for on-the-job convenience. No. 5417 is slotted for attaching to 2″ wide (51 mm) belts. No. 5417T has tunnel loop to permit use on wider belts or to slide over O-rings, buckles and other accessories up to 3-1/2″ (89 mm). MADE OF LEATHER.

Mfg. # CSI Ref. # Nominal Size
in. cm
5417 CS-11-2130 3-1/4 x 11 8 x 28
5417T CS-11-2131 3-1/4 x 12-1/4 8 x 31

WARNING: Always wear eye protection.

The Most Trusted and Respected Company in Rigging and Overhead Lifting.

Connect with us