Klein® Bars & Pins :: Certified Slings & Rigging

Klein® Bars & Pins

Connecting Bars

Provide extra leverage when positioning steel members and aligning bolt holes. These drop-forged fit-up bars are pointed on one end; the chisel-end is available straight or at a 15° angle to give greater leverage. Hexagonal or round.

Round Bars

Mfg. #	CSI Ref. #	Diameter		Length
Mfg. #	CSI Ref. #	in.	mm	in.	cm
3245	CS-11-2115	3/4	19.1	30	76
3246	CS-11-2116	7/8	22.2	36	91
3247	CS-11-2117	3/4	19.1	24	61
3248	CS-11-2118	7/8	22.2	30	76
3241*	CS-11-2119	3/4	19.1	30	76

* Similar to round bar No. 3245 above but chisel-end is straight.

Hexagonal Bars

Mfg. #	CSI Ref. #	Hex. Diameter		Length
Mfg. #	CSI Ref. #	in.	mm	in.	cm
3242	CS-11-2120	3/4	19.1	30	76
3243	CS-11-2121	7/8	22.2	36	91
3244	CS-11-2122	3/4	19.1	24	61
3240*	CS-11-2123	3/4	19.1	30	76

* Similar to hexagonal bar No. 3242 above but chisel-end is straight.

Barrel-Type Drift Pins

Machined from forge-quality alloy steel. Tapers are uniform and blend into body diameter. Tough, drop-forged steel will properly end-pein in use. Heat-treated. Black finish.

Mfg. #	CSI Ref. #	Max. Diameter		Point Diameter		Overall Length
Mfg. #	CSI Ref. #	in.	mm	in.	mm	in.	mm
3260	CS-11-2124	11/16	17.5	5/16	7.9	7-1/2	191
3261	CS-11-2125	13/16	20.6	7/16	11.1	8	203
3262	CS-11-2126	15/16	23.8	1/2	12.7	8	203
3263	CS-11-2127	1-1/16	27	9/16	14.3	8	203

All dimensions are nominal.

Broad-Head Bull Pins

Mfg. #	CSI Ref. #	Top Diameter		Point Diameter		Length
Mfg. #	CSI Ref. #	in.	mm	in.	mm	in.	mm
3255	CS-11-2128	1-1/4	31.8	5/16	7.9	13	330
3256	CS-11-2129	1-1/16	27	1/4	6.4	10	254

All dimensions are nominal

A drop-forged, heat-treated bull pin which increases efficiency by providing a larger striking surface. Design of the head also reduces chance of pin slipping from the hand when aligning holes. Angled head and smooth blending of radii increase strength and reduce the danger of chipping. Below the head, squared-off shoulders have been forged to provide a surface for applying wrench to loosen wedged bull pins. Long, even taper reduces binding and hang-up. Klein broad-head bull pins offer added resistance to ?mushrooming?, permitting much longer use than is possible with conventional designs. Black finish. Note: OSHA specifically states that, ?impact tools such as drift pins, wedges, and chisels, shall be kept free of mushroomed heads.?

Bull-Pin Holders

Holders for Klein bull pins. Attach to belt for on-the-job convenience. No. 5417 is slotted for attaching to 2? wide (51 mm) belts. No. 5417T has tunnel loop to permit use on wider belts or to slide over O-rings, buckles and other accessories up to 3-1/2? (89 mm). MADE OF LEATHER.

Mfg. #	CSI Ref. #	Nominal Size
Mfg. #	CSI Ref. #	in.	cm
5417	CS-11-2130	3-1/4 x 11	8 x 28
5417T	CS-11-2131	3-1/4 x 12-1/4	8 x 31

WARNING: Always wear eye protection.